Tool Tethering Kit for Small Hand Tools - 1lb / 0.5kg
The Squids® Hand Tool Tethering Kit includes a 3156 Coil Tool Lanyard with Single Carabiner and the 3740 Hand Tool Attachment Trap – Slips™ Variety 4-Pack. This tool tethering kit allows you to tether four different sized screwdrivers and hex key wrenches making it easy to use your tools on the job while preventing dropped objects when working at-heights.
The Squids 3194 Hand Tool Tethering Kit includes a 3156 Coil Tool Lanyard with Single Carabiner and the 3740 Hand Tool Attachment Trap Slips Variety 4-Pack. This tool tethering kit allows you to tether 4 different sized screwdrivers and hex key wrenches making it easy to use your tools on the job while preventing dropped objects when working at-heights.</p>
The 3156 Coil Tool Lanyard is more than just a small tool and hard hat lanyard. Built and tested to endure tough conditions and rated to support weight up to 2lbs / 0.9kg, the coiled lanyard is made with a low-profile design and durable plastic. With the lightweight aluminum carabiner on one end and a tethering loop on the other, it easily connects to tool anchors and attachments, even while wearing gloves. The coiled tether design reduces lanyard length to prevent snag and tangle hazards. The coil stretches from a compact 12in to 48in / 30cm to 122 cm.</p>
STRAIGHTFORWARD INSTALLATION</h3>
No additional install tools or complicated taping or shrinking! The Slips design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect the Squids 3156 Coil Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.</p>
Simply poke the end of the hand tool through the orange interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. To remove the Slips, simply push on the tab to loosen and then slide it off the shaft of the tool. No adhesive residue or mess will be left behind!</p>
PERFECT FOR SMALL HAND TOOLS</h3>
Small hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids Hand Tool Slips allow you to tether tools up to 1lb. based on their diameter. Four sizes of Slips are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size.</p>
Squids Radio Holster Trap, Black, Small, 19772 at Tractor Supply Co.
Ergodyne Squids 3772 Radio Holster Trap - Jendco Safety Supply
欠品カラー再入荷！ BY コイルシンプル Install Ford グローブ
Tool Tethering Kit for Small Hand Tools - 1lb / 0.5kg
100% Polyester Meets the ANSI/ISEA 121-2018 standard Kit includes: One Variety 4-Pack 3740 Hand Tool Attachment Trap - Slips One 3156 Coil Low Profile
Hand Tool Tethering Kit for Screwdrivers & Hex Key Wrenches, Includes 4 Tool Attachment Slips & 1 Tool Lanyard, Weight Capacity 1 lb, Ergodyne Squids
Squids Ergodyne 3195 Cell Phone Tool Tethering Kit- 1lb, Kit in the Safety Accessories department at
The Squids 3194 Hand Tool Tethering Kit includes both a Squids 3156 Coil-Cable Tool Lanyard and a pack of four Squids 3740 Hand-Tool Slip Traps, making it ideal for retrofitting a wide variety of fastener drivers for tethering. Prepare up to four differently sized screwdrivers, nut-drivers and/or hex keys for quick and easy interchanges, so you can focus on the task at hand, while minimizing the potential for inconvenient and potentially very dangerous tool drops when you're working at heights.
Ergodyne Squids 3194 Hand Tool Tethering Kit - 1lb
Squids Ergodyne 3194 Hand Tool Tethering Kit- 1lb, Kit in the Safety Accessories department at
Ergodyne Squids 3772 Radio Holster Trap - Jendco Safety Supply
Search Results For Hand Tools & Hydraulic Tools - Tools - Tools & Testers - Categories - Products - Elliott Electric Supply
